Kohler Power Systems 14/20RESA User Manual Page 67
- Page / 72
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
TP-6804 12/11 67Section 6 Troubleshooting
Section 6 Troubleshooting
6.1 Introduction
Use the troubleshooting charts in this section to
diagnose and correct common problems. First check for
simple causes such as a dead engine starting battery,
loose connections, or an open circuit breaker. The
charts include a list of common problems, possible
causes of the problem, and recommended corrective
actions.
If the procedures in this manual do not explain how to
correct the problem, contact an authorized Kohler
distributor/dealer. Maintain a record of repairs and
adjustments performed on the equipment. Use the
record to help describe the problem and repairs or
adjustments made to equipment.
6.2 Fault Messages
The RDC2/DC2 controller displays fault messages to
aid in troubleshooting. Selected fault messages and
recommended checks are listed in Figure 2-3.
Identify and correct the cause of the fault condition.
Then reset the controller after a fault shutdown. See
Section 2.5.4.
6.3 Circuit Protection
If the generator set circuit breaker trips repeatedly,
contact an authorized Kohler distributor/ dealer for
service.
6.3.1 Controller I nternal Circuit
Protection
The controller is equipped with internal circuit
protection. A fault message, Accy PwrOver Warning or
MainPwrOverL Shutdown, is displayed if this internal
protection is activated. Press OFF to reset. Contact an
authorized Kohler distributor/ dealer for service.
6.3.2 Line Circuit Breaker
The line circuit breaker interrupts the generator output in
the event of a fault in the wiring between the generator
and the load. If the circuit breaker trips, reduce the load
and switch the breaker back to the ON position.
6.3.3 Auxiliary Winding Circuit Breaker
A resettable circuit breaker protects the alternator. The
circuit breaker is located in the controller’s service
access area. See Figure 6-1.
6.4 Controller Service Access
The alternator winding circuit breaker is accessible from
the front of the controller. Remove the service access
door to reach the circuit breaker. See Figure 6-1.
A USB port is also located in the service access area.
Some controller settings can be adjusted using a laptop
computer with Kohler SiteTech software. Use a USB
cable with a mini-B connector to connect the controller to
your PC. See TP-6701, SiteTech Software Operation
Manual, for more information.
2
GM
1. USB port (mini-B)
2. Alternator winding circuit breaker
1
Figure 6-1 Controller Service Access (cover
removed)
- 14/20RESA 1
- 14/20RESAL 1
- Operation 1
- Controller Identification 2
- Engine Identification 2
- Table of Contents 3
- Table of Contents, continued 4
- TP-6804 12/116 6
- Accidental Starting 7
- Engine Backfire/Flash 8
- Exhaust System 8
- Fuel System 9
- Hazardous Noise 9
- Hazardous Voltage/ 9
- Moving Parts 9
- Heavy Equipment 10
- Hot Parts 10
- Introduction 11
- Nameplate 12
- Emission Information 12
- Service Assistance 13
- RDC2 Controller Features 16
- DC2 Controller Features 17
- 1.7 Accessories 18
- 1.8 Service Views 19
- 2.1 Prestart Checklist 21
- 2.3 Generator Set Operation 21
- RXT Transfer Switch 22
- RDT or RSB Transfer Switches 22
- 2.4 Exercise 23
- 2.5 Faults 24
- Fault Shutdown 25
- Switch Controller 29
- 3.2 Controls and Indicators 29
- 3.2.1 Controller Keypad 30
- 3.2.2 LED Indicators 30
- 3.2.3 LCD Display 31
- 3.3 Controller Power 32
- 3.4 Battery Charging 32
- 3.5 Changing Settings 32
- 3.6 Setting the Exerciser 34
- 3.7 RDC2 Controller Menus 36
- 3.8 Main Menu 36
- 3.9 Overview Menu 37
- 3.10 Engine Metering Menu 37
- 3.11 Generator Metering Menu 38
- 3.13 Genset Run Time Menu 39
- 3.14 Genset System Menu 40
- 3.15 ATS Status Menu 41
- 3.16 ATS Configuration Menu 42
- 3.17 Date and Time Menu 43
- Submenu (OnCue Password) 45
- 3.18.3 RBUS Information 46
- 3.18.4 Remote Devices Submenu 47
- 3.19 Programmable Interface 48
- Module (PIM) Status Menu 48
- 3.21 Event Log 50
- 4.2 Controls and Indicators 51
- 4.2.1 Controller Keypad 52
- 4.2.2 LED Indicators 52
- 4.3 Controller Power 53
- 4.4 Battery Charging 53
- 4.5 Exercise 54
- 4.6 Event Log 54
- 4.7 Maintenance Timer 55
- 4.8 OnCue Password 55
- 5.1 Scheduled Maintenance 57
- 5.2 Lubrication System 60
- 5.2.6 Oil Cooler 20RESA/RESAL 61
- 5.3 Spark P lugs 62
- 5.4 Air Cleaner Service 62
- 1. Knobs (qty.2) 63
- 2. Cover 63
- 3. Paper element 63
- 5.5 Cooling System 64
- 5.6 Exhaust System 64
- 5.7 Battery 65
- 5.8 Storage Procedure 66
- Section 6 Troubleshooting 67
- 6.5 Troubleshooting 68
- Appendix A Abbreviations 69
- TP-6804 12/11 72
© 2020, manymanuals.com. All rights reserved. | 1.421 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals