Groove
x6
3
1
2
x2
Face
Top View
C
C
D
D
Wall
Screw Cover
Screw Cover
#8-18 x 1-1/2"
x2
Notch
1/32" (1 mm)
Cut Line
"B" Mark
B
B
Top Track
Tin Snips
32 Teeth Per Inch Blade
Masking Tape
100% Silicone Sealant
Rubber Mallet
5/16" Masonry
Bit for Tile
5/16"
3/32", 9/64", 5/32"
Sliding Shower Doors
Sliding Bath Doors
1205305**
Hanger Bracket Kit
1221883
Hardware Skin Pack
Top Bumper
1224786
Gasket
1199110
Barrel Nut
1050048-B
Screw
1051142-A
Roller
1044585
Bolt
1077763-A
1031943**
Screw Cover
1056868-A
Screw
1225278
Center Guide
1058626-02**
Bottom Track
1162676-07**
Wall Jamb
[68-13/16" (1748 mm)]
1162676-04** [56-13/16" (1443 mm)]
1077762
Anchor
1199426-01**
Hanger Bracket
Screw
1048208-C
1053530
Insert
1220609-01**
Top Track
1225277
Bottom
Right Bumper
1225276
Bottom
Left Bumper
Bottom Wall
Jamb Notch
#8-18 X 1-1/2"
Bottom Wall
Jamb Notch
#8-32 X 3/8"
8-32 X 1/4"
Serial Number Label
1226469**
Towel Bar Skin Pack
1221364-01**
Towel Bar
#6-20 X 1/2"
1222364-NA**
29-1/2" x 55-19/32"
(749 mm x 1411 mm)
1223197-NA**
23-1/2" x 67-19/32"
(597 mm x 1717 mm)
1222365-NA**
29-1/2" x 67-19/32"
(749 mm x 1717 mm)
Door Panel*
1/4" (6 mm)
Cut Line
"A" Mark
A
A
Insert
Bottom Track
Slide the notched end of the insert into the
groove in the bottom track, grasp the insert and
pull to the opposite end. Trim the insert flush
with the bottom track.
Measure distance "A." On the bottom track,
measure "A." Subtract 1/4” (6 mm) or the width
of a number 2 pencil from "A;" mark and cut the
bottom track.
Position the bottom track on the center of the
ledge. If needed, file the ends to match the
corners.
Position the bottom track on the ledge with the
front face evenly spaced (D) along the front
edge, even gaps on each side (C). Tape the
bottom track in place and mark the position.
Important! The bottom track and wall jamb
must sit flat against the shower ledge and the
wall. If needed, trim and file the wall jamb. Use
a coin to match and to transfer the corner radius
of the shower to the wall jamb.
Position the wall jambs over the bottom track.
Plumb using a level. Secure with tape. For each
screw hole, mark the locations or drill a pilot
hole.
Remove the wall jambs. Drill 5/16” holes at each
mark and insert the anchors.
Apply silicone sealant in the groove on the
underside of the bottom track. Secure the bottom
track to the ledge along the marked location
with tape.
Install both wall jambs. Secure the wall jambs
with screws. If you are using a power drill, take
care not to strip the screw heads. Install the
screw covers.
Measure distance “B” above the wall jambs.
Subtract 1/32” (1 mm) or the width of a saw
blade from “B.” Mark and cut the top track.
Sliding Shower Door
WARNING: Risk of serious injury. Damage prior to installation can
result in glass shattering. Inspect the glass and all parts for damage
before installation.
WARNING: Risk of serious injury. Improper installation can result
in glass shattering. Follow all installation instructions.
WARNING: Risk of serious injury. Do not cut tempered glass.
Tempered glass will shatter if cut.
WARNING: Risk of serious injury. Shower door and side panels
can shatter. Regularly inspect the glass and all parts for damage,
missing, or loose parts.
WARNING: Risk of serious injury. Always wear safety glasses
while cutting and drilling.
NOTICE: Do not touch the edges of the tempered glass with tools or any
other hard objects. Do not set the unframed tempered glass directly on the
floor or any hard surface.
IMPORTANT: Leave this manual for the end user.
Read these instructions before installing or using this product. Keep these
instructions in a safe location for future reference.
These instructions can also be found at www.kohler.com
IMPORTANT! Do not cut the top track the same length as the bottom track.
• Two people are recommended for this installation.
• Walls must be within 3/8” (10 mm) of plumb.
• Cover drain with tape to avoid loss of small parts.
• Unpack the door in an area with adequate space and no sharp corners or
surfaces that may cause glass breakage.
• Follow the silicone sealant manufacturer’s instructions for application and
curing time.
1
1220846-2-B
USA/Canada: 1-800-4KOHLER
México: 001-800-456-4537
1220846-2-B
Installation and Care Instructions
*Call Customer Care Center to order replacement parts.
**Finish/color code must be specifi ed when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________
Required Tools Parts Identifi cation
2 3 4
7 86 9
1 5
10
K-R709062, K-R709063, K-R709064
kohler.com
(16 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals