Kohler K-1418-G-0 Installation Guide Page 19
- Page / 72
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Test Run the Bath (cont.)
Rotate the outer ring to the chromatherapy icon, then press ″OK″. The chromatherapy lights will
automatically and continuously cycle through the eight colors; white, violet, indigo blue, aqua blue,
green, yellow, orange and red. One cycle through all eight colors takes approximately one minute.
Press ″OK″ while the chromatherapy mode is active to turn off the chromatherapy lights.
Rotate the outer ring to the chromatherapy specific color icon, then press ″OK″. Use the up or down
arrows to reach the desired color.
Press ″OK″ again to turn off the chromatherapy lights.
Operate the Automatic Purge Cycle
NOTE: The automatic purge cycle occurs after the bath is drained. It operates at low speed for about two
minutes to remove any residual water from the air channels.
If required, fill the bath to a level at least 2″ (5.1 cm) above the top of the highest airjet.
Drain the bath.
When the water level drops below the level sensor probes, verify that the blower motor starts at low
speed.
After about two minutes, verify that the blower motor stops.
Operate the Manual Purge Cycle
With the bath drained, rotate the outer ring to the purge cycle icon.
Press the ″OK″ icon.
Observe that the blower motor starts in purge cycle. Residual water will blow out from the air
channels.
After the blower motor has operated for about two minutes, observe that the blower motor stops.
Place the protective drop cloth over the bath.
Turn off the power to the bath.
Kohler Co. 19 1035472-2-H
- Installation Guide 1
- Important Information 2
- Factory Assembled Features 3
- Table of Contents 4
- Tools and Materials 4
- Before You Begin 4
- Bath may be installed next 7
- 3. Secure the Bath 8
- 4. Install the Plumbing 9
- Electrician to provide 10
- Remove the Blower Motor 11
- Remove the Check Valve 11
- Prepare the Site 11
- Remove screws, remove cover 13
- Second Junction Box 15
- Control Power Junction Box 15
- 12. Test Run the Bath 17
- 11. Complete the Installation 17
- 13. Operate the Keypad 20
- Troubleshooting 21
- Guide d’installation 24
- Informations importantes 24
- Sommaire 26
- Outils et matériels 26
- Avant de commencer 26
- Panneaux 28
- 3. Sécuriser la baignoire 30
- 4. Installer la plomberie 31
- L'électricien doit 32
- Retirer le moteur-souffleur 34
- Préparer le site 34
- Second boîtier de jonction 38
- 11. Terminer l’installation 40
- 13. Fonctionnement du clavier 43
- Dépannage 44
- Guía de instalación 47
- Información importante 47
- Contenido 49
- Herramientas y materiales 49
- Antes de comenzar 49
- Panel de 51
- La bañera se puede instalar 52
- 3. Fije la bañera 53
- 4. Instale la plomería 54
- Retire el motor soplador 57
- Prepare el sitio 57
- (10,2 cm) del motor soplador 59
- Segunda caja de empalmes 61
- 11. Termine la instalación 63
- 13. Haga funcionar el teclado 66
- 1035472-2-H 70
Related products and manuals for Unknown Kohler K-1418-G-0
Unknown Kohler K-4918-0 Installation Guide
(20 pages)
(20 pages)
Unknown Kohler K-1124-95 Installation Guide
(40 pages)
(40 pages)
Unknown Kohler K-102-PB Installation Guide
(16 pages)
(16 pages)
Unknown Kohler K-9349-S Installation Guide
(12 pages)
(12 pages)
Unknown Kohler K-1132-96 Installation Guide
(24 pages)
(24 pages)
Unknown Kohler K-2230-4-0 Installation Guide
(16 pages)
(16 pages)
Unknown Kohler K-11372-BN Installation Guide
(16 pages)
(16 pages)
Unknown Kohler K-4645-47 Installation Guide
(28 pages)
(28 pages)
Unknown Kohler K-11344-47 Installation Guide
(28 pages)
(28 pages)
Gai-tronics TDN9413A Stat-Alert Signaling Module Kit manuály
Uživatelské manuály a uživatelské příručky pro Komunikace Gai-tronics TDN9413A Stat-Alert Signaling Module Kit.
Poskytujeme 1 manuály pdf Gai-tronics TDN9413A Stat-Alert Signaling Module Kit ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comments to this Manuals