Kohler K-1418-G-0 Installation Guide Page 20
- Page / 72
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
13. Operate the Keypad
Available modes/features will be illuminated in blue. Active modes will be illuminated in green.
Power On/Off Turns the blower motor on and off.
Outer Ring Rotate the outer ring to the desired mode. The selected mode will flash blue.
OK Activates the desired mode. The active mode will flash green.
Air Flow Mode Air flow is directed through any combination of the airjets in the selected zones. Air flow
can be adjusted with the arrow buttons. When the surge mode is selected, the air flow
mode stops. When the air flow mode is selected while operating in the surge mode, the
surge mode stops.
Zone 1 Selects or deselects the air flow through Zone 1.
Zone 2 Selects or deselects the air flow through Zone 2.
Zone 3 Selects or deselects the air flow through Zone 3.
Surge Mode When active, the air flow ramps up from minimum to maximum and then down again to
minimum. The surge speed is adjustable between approximately 10 seconds to 60 seconds
by using the up or down buttons. The up and down arrow buttons can be used to adjust
the surge speed. Zones can be selected or deselected when in the surge mode.
Up Arrow Increases the air flow when the air flow mode is active. Increases the pulse speed when
the surge mode is active.
Indicator Bar Shows the air flow volume when operating in the air flow mode. Shows the surge speed
when operating in the surge mode.
Down Arrow Decreases the air flow when the air flow mode is active. Decreases the pulse speed when
the surge mode is active.
Chromatherapy
Cycle
Rotate the outer ring to select this mode, then press OK. The chromatherapy lights will
automatically and continuously cycle through eight colors. One cycle through all eight
colors takes approximately one minute. Only one of the two keypads controls this mode.
Purge Mode Select to initiate the purge mode manually. The purge cycle will not start if there is water
in the bath. The purge mode blows any residual water out of the air channels. The blower
motor starts and runs at a low speed for about two minutes. An automatic purge cycle
occurs when the bath is drained and the water level falls below the level sensors.
Chromatherapy
Specific Color
Rotate the outer ring to select this mode. Press OK, press the up or down arrow to select a
color, then press OK again. Only one of the two keypads controls this mode.
Sleep Mode To enhance your bathing experience, the keypad is programmed to darken after
approximately 15 seconds of inactivity. Only the last feature selected will remain
illuminated. To resume normal operation, press any key or turn the outer ring.
Approximately 60 seconds after all equipment is turned off, the keypad will darken
completely to conserve power. Press the power button or turn the outer ring to reactivate
the keypad.
Air Flow Mode
Activates Mode Selected
Power On/Off
Indicator Bar
Decrease Flow or Surge
Increase Flow or Surge
Zone 1
Zone 2
Zone 3
Surge Mode
Purge Mode
Chromatherapy Specific
Color (if provided)
Chromatherapy Cycle
(if provided)
Rotate Outer Ring to
Access Desired Mode
1035472-2-H 20 Kohler Co.
- Installation Guide 1
- Important Information 2
- Factory Assembled Features 3
- Table of Contents 4
- Tools and Materials 4
- Before You Begin 4
- Bath may be installed next 7
- 3. Secure the Bath 8
- 4. Install the Plumbing 9
- Electrician to provide 10
- Remove the Blower Motor 11
- Remove the Check Valve 11
- Prepare the Site 11
- Remove screws, remove cover 13
- Second Junction Box 15
- Control Power Junction Box 15
- 12. Test Run the Bath 17
- 11. Complete the Installation 17
- 13. Operate the Keypad 20
- Troubleshooting 21
- Guide d’installation 24
- Informations importantes 24
- Sommaire 26
- Outils et matériels 26
- Avant de commencer 26
- Panneaux 28
- 3. Sécuriser la baignoire 30
- 4. Installer la plomberie 31
- L'électricien doit 32
- Retirer le moteur-souffleur 34
- Préparer le site 34
- Second boîtier de jonction 38
- 11. Terminer l’installation 40
- 13. Fonctionnement du clavier 43
- Dépannage 44
- Guía de instalación 47
- Información importante 47
- Contenido 49
- Herramientas y materiales 49
- Antes de comenzar 49
- Panel de 51
- La bañera se puede instalar 52
- 3. Fije la bañera 53
- 4. Instale la plomería 54
- Retire el motor soplador 57
- Prepare el sitio 57
- (10,2 cm) del motor soplador 59
- Segunda caja de empalmes 61
- 11. Termine la instalación 63
- 13. Haga funcionar el teclado 66
- 1035472-2-H 70
Related products and manuals for Unknown Kohler K-1418-G-0
Unknown Kohler K-4918-0 Installation Guide
(20 pages)
(20 pages)
Unknown Kohler K-1124-95 Installation Guide
(40 pages)
(40 pages)
Unknown Kohler K-102-PB Installation Guide
(16 pages)
(16 pages)
Unknown Kohler K-9349-S Installation Guide
(12 pages)
(12 pages)
Unknown Kohler K-1132-96 Installation Guide
(24 pages)
(24 pages)
Unknown Kohler K-2230-4-0 Installation Guide
(16 pages)
(16 pages)
Unknown Kohler K-11372-BN Installation Guide
(16 pages)
(16 pages)
Unknown Kohler K-4645-47 Installation Guide
(28 pages)
(28 pages)
Unknown Kohler K-11344-47 Installation Guide
(28 pages)
(28 pages)
© 2020, manymanuals.com. All rights reserved. | 0.601 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals