Kohler K-1110-G-0 Installation Guide download pdf (Page 22)

Troubleshooting (cont.)

Symptoms Probable Causes Recommended Action

6. Blower motor starts, some

but not all airjets are

bubbling.

A. Blower motor speed is too low. A. Increase speed set point to blower

motor.

B. Blower motor inlet is blocked. B. Clean blower motor inlet.

C. Blower motor does not work. C. Replace the blower motor.

D. Blower motor discharge is

blocked.

D. Check blockage.

E. Check valve does not work. E. Replace the check valve.

F. Air jets are clogged. F. Use a small between-the-teeth

dental brush and white vinegar.

Dip the brush in the vinegar, brush

the hole, rinse the brush in clean

water, and then use the wet rinsed

brush to rinse the hole.

G. Some zones are closed. G. Operate all zones.

7. Blower motor runs but no

air bubbles are formed.

A. Blower motor inlet is blocked. A. Clean blower motor inlet.

B. Air jets are clogged. B. Use a small between-the-teeth

dental brush and white vinegar.

Dip the brush in the vinegar, brush

the hole, rinse the brush in clean

water, and then use the wet rinsed

brush to rinse the hole.

C. Check valve does not work. C. Replace the check valve.

D. Blower motor does not work. D. Replace the blower motor.

E. Control does not work. E. Replace the control.

8. Blower motor operates,

air bubbles are formed,

zone controls work, but

variable speed feature

does not work.

A. Blower motor inlet is blocked. A. Clean blower motor inlet.

B. Loose, disconnected, or

damaged wiring harness.

B. Check wiring for proper

connections. Replace the wiring

harness if necessary.

C. User keypad does not work. C. Replace the user keypad.

D. Blower motor does not work. D. Replace the blower motor.

E. Control does not work. E. Replace the control.

9. Blower motor won’t turn

off when the power

button on user keypad is

pressed.

A. User keypad does not work. A. Replace the user keypad.

B. Loose, disconnected, or

damaged wiring harness.

B. Check wiring for proper

connections. Replace the wiring

harness if necessary.

C. Control does not work. C. Replace the control.

10. A zone does not produce

air bubbles but another

zone operates normally.

A. Zone is not selected. A. Select the zone according to the

instructions in the ″Conﬁrm Proper

Operation″ section.

B. Butterﬂy valve does not work. B. Replace the butterﬂy valve.

C. Loose, disconnected, or

damaged wiring harness.

C. Check wiring for proper

connections. Replace the wiring

harness if necessary.

D. User keypad does not work. D. Replace the user keypad.

E. Control does not work. E. Replace the control.

11. Surge mode does not

work.

A. User keypad does not work. A. Replace the user keypad.

B. Control does not work. B. Replace the control.

12. Water spillage or damage

observed under the bath.

A. Drain or overﬂow leaking. A. Repair or replace the drain

assembly according to the

manufacturer’s instructions.

B. Wall, deck, and/or shower door

is improperly sealed.

B. Apply silicone sealant at the seams

between the bath and the wall,

deck, or door.

1035472-2-J 22 Kohler Co.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 71 72

Comments to this Manuals

No comments

Kohler K-1110-G-0 Installation Guide Page 22

Comments to this Manuals

Related products and manuals for Unknown Kohler K-1110-G-0