Kohler K-14274-BR-96 Installation Guide download pdf (Page 3)

1007251-2-

Kohler Co.

DRAW PRELIMINARY FAUCET CENTERLINE

1. Draw the distance determined in F AUCET L OCA TION as the

preliminary centerline on the cut-out template. It should be parallel

and behind the cut-out template reference line (located on the

cut-out template).

NOTE: On the full-size rim section found on the cut-out

template, mark the preliminary faucet centerline dimension.

This will be used to DETERMINE FINAL F AUCET CENTER-

LINE.

DETERMINE FINAL FAUCET CENTERLINE

NOTE: If you are installing a tiled-in lavatory, proceedto Step 1B.

The preliminary faucet line from DRAW PRELIMINARY

FAUCET LINE is the final faucet li ne in this case.

1. When this preliminary faucet centerline has been drawn the

spout must be checked for three items:

A. Refer to Fig. #2. For low profile faucet spouts, the

distance between the faucet spout and the lavatory rim must be a

minimum of 1/4” (6mm). Use the faucet spout, the preliminary

faucet centerline,and the full size rim sectiononthe cut-outtemplate

to check this. If there is not 1/4” (6mm) clearance, move the

preliminary faucet centerline back. Recheck the clearance until you

have 1/4” (6mm). Measure the distanceof thenew faucetcenterl ine.

Redraw the new faucet centerline behind the reference line on the

cut-out template. Remark this dimension on the full size rim section.

This is the final faucet centerline.

2” (5cm) Min.

1/4” (6mm)Min.

Fig. #3

B. Refer to Fig. #3. Check to be sure the water stream will

project 2” (5cm) minimum into the lavatory basin to allow adequate

area forhand washing. Use theapproximate faucetspout angle, the

final faucet centerline and the full-size rim section from the cut-out

template to ensure this clearance. If this cannot be accomplished,

the faucet is not optimally matched for this lavatory and may not

operate on this lavatory to the owner’s satisfaction. You may wish to

consider an alternate faucet .

C. Refer to Fig. #3. Check for compliance with all state and

local plumbing codes, including air gap standards.

2” (5cm)

Min.

Fig. #4

Air

Gap

FAUCET CLEARANCE WITH BACKSPLASH

NOTE: 2-1/2” (6,4cm)of space is required for the KohlerBravura

widespread and Cirrus Sheetflow faucet spouts.

1.Refer to Fig. #4. Draw a line 2” (5cm) behind the final faucet

centerline on the cut-out template. This is the minimum backsplash

locator line. It is drawn to ensure adequate clearance behind the

faucet for proper installation. It will also help position the lavatory on

the countertop. Cut along this backsplash locator line. Save the

section of the cut-out template with the lavatory rim and cut-out

lines.

2”

Countertop Backsplash Backsplash Locator Line

L of Fitting

On Countertop

Counter top

Fig. #5

(5cm)

Cut-Out Template

INSTALLATION

1. To rem ov e old lav atory, turn of f water supp lies. Turn the

lavatory faucet on to drain water from the lines. Disconnect and

remove water supply tubes. Disconnect drain and remove trap.

CAUTION: To remove steel frame lavatories, remove

clips or fasteners under lavatory that hold lavatory to counter.

Do not remove clips that hold frame to fixture.

1 2 3 4 5 6 7 8 ... 15 16

Comments to this Manuals

No comments

Kohler K-14274-BR-96 Installation Guide Page 3

Comments to this Manuals

Related products and manuals for Unknown Kohler K-14274-BR-96