Kohler K-1914-GRW-0 Installation Guide Page 2
- Page / 168
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Important Information
Read all instructions before using or installing this product.
WARNING: When using electrical products, basic precautions should always be followed,
including the following:
DANGER: Risk of electric shock. Connect only to a circuit protected by a Ground-Fault
Circuit-Interrupter (GFCI)*.
Building materials and wiring should be routed away from the pump body and other heat-producing
components of the unit.
Install to permit access for servicing.
A pressure wire connector marked ″Earth/Ground″ is provided within the wiring compartment. To reduce
the risk of electric shock, connect this connector to the grounding terminal of your electric service or supply
panel with copper wire equivalent in size to the circuit conductor supplying this equipment.
Pressure wire connectors are provided on the exterior of the junction box or control within this unit to permit
connection of a bonding conductor between this unit and all other exposed metal in the vicinity, as needed to
comply with local requirements.
Grounding is required. The unit should be installed by a qualified service representative, and grounded.
WARNING: Risk of injury or property damage. Please read all instructions thoroughly before
beginning installation, including the following requirements.
WARNING: Risk of electric shock. A qualified electrician should make all electrical connections.
WARNING: Risk of electric shock. Disconnect power before servicing.
NOTICE: Follow all local plumbing and electrical codes. In Canada, install this unit in accordance with
the Canadian Electrical Code, Part 1.
*Outside North America, this device may be known as a Residual Current Device (RCD).
Product Information
Electrical Requirements
WARNING: Risk of burns, fire, electric shock, or injury to persons. Do not operate the blower if
the blower supply cord is damaged. For proper guidance to have this product repaired, please call:
1-800-4KOHLER from within the USA and Canada, or 001-800-456-4537 from Mexico.
NOTE: If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or
similarly qualified persons in order to avoid a hazard.
The installation must have a Class A Ground-Fault Circuit-Interrupter (GFCI*). The GFCI protects against
line-to-ground shock hazard. Use a 120 V, 15 A, 60 Hz dedicated service for the bath with airjets.
*Outside North America, this device may be known as a Residual Current Device (RCD).
Product Notices
NOTICE: Keep the area around the blower motor clean and free of debris. Ensure that the area around
the blower motor is free of sawdust, insulation, dirt, or other small loose debris. Such material could clog
the blower motor air ducts and reduce the air flow through the blower.
NOTICE: This product contains an automatic water purge mode that turns the blower on for 2 minutes
approximately 30 minutes after the unit is turned on and drains.
1128535-2-F 2 Kohler Co.
- Installation Guide 1
- Important Information 2
- Factory-Assembled Features 3
- Table of Contents 4
- Tools and Materials 4
- Before You Begin 5
- Parts Identification 6
- 1. Construct the Framing 7
- 2. Confirm the Correct Cutout 9
- All Installations 10
- 5. Remove the Door 13
- 1128535-2-F 16 Kohler Co 16
- 7. Remove the Receptor Tray 17
- 8. Disconnect the Components 18
- Kohler Co. 19 1128535-2-F 19
- 9. Position the Bath 20
- 10. Level and Secure the Bath 22
- 12. Install the Receptor Tray 24
- 14. Install the Door 28
- 15. Attach the Counterweights 29
- 16. Connect the Components 31
- 17. Adjust the Bath Door 32
- GFCI-Protected Receptacle 36
- Power Supply 36
- Heating Surface 36
- 20. Confirm Airjet Operation 37
- Keypad Operation 38
- 22. Install the Finished Wall 41
- Troubleshooting 41
- Guide d’installation 54
- Notices du produit 55
- Pièces assemblées en usine 55
- Sommaire 56
- Outils et matériaux 56
- Avant de commencer 57
- Identification des pièces 58
- 1. Construire la charpente 59
- Toutes les installations 61
- 5. Retirer la porte 65
- 7. Retirer le bac collecteur 69
- 8. Déconnecter les composants 70
- 9. Positionner la baignoire 72
- 14. Installer la porte 80
- 15. Attacher les contrepoids 81
- 16. Connecter les composants 83
- Alimentation électrique 88
- Surface de chauffage 88
- Fonctionnement du clavier 89
- 22. Installer le mur fini 95
- Dépannage 95
- Guía de instalación 110
- Avisos sobre el producto 111
- Contenido 112
- Herramientas y materiales 112
- Antes de comenzar 113
- Identificación de las piezas 114
- Todas las instalaciones 115
- 5. Retire la puerta 121
- 8. Desconecte los componentes 126
- 9. Coloque la bañera 128
- 10. Nivele y fije la bañera 130
- 14. Instale la puerta 136
- 15. Fije los contrapesos 137
- 16. Conecte los componentes 139
- Tomacorriente protegido 144
- Superficie de calefacción 144
- Funcionamiento del teclado 145
- 22. Instale la pared acabada 151
- Guía para resolver problemas 151
- 1128535-2-F 166
Related products and manuals for Unknown Kohler K-1914-GRW-0
Unknown Kohler K7160AFCP User's Guide
(24 pages)
(24 pages)
Unknown Kohler K9000CP Specifications
(2 pages)
(2 pages)
Unknown Kohler K7160AFCP Specifications
(2 pages)
(2 pages)
Unknown Kohler K7160AFCP User's Guide
(1 pages)
(1 pages)
© 2020, manymanuals.com. All rights reserved. | 0.504 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals