Kohler K-1914-GRW-0 Installation Guide Page 7
- Page / 168
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
1. Construct the Framing
All Installations
NOTICE: Measure your product for site preparation. Note the model number located on the blower
motor, then visit the product page at www.kohler.com for more information.
NOTICE: Adequate floor support must be provided.
NOTICE: Do not support the weight of the bath by the perimeter of the rim. To avoid damage to the
product, support the bath by its base or feet.
IMPORTANT! This product requires three 1-1/2″ diameter drain outlets, three P-traps, and three separate
lines to the stack. In an ideal configuration, none of the drains should be combined, as performance may
suffer and the potential for backflow will increase. If required, the two bathing vessel drains (#1 and #2 in
diagram) may be combined downstream from the P-traps into a single 3″ diameter drain line.
IMPORTANT! The drain for the receptor tray (#3) requires a dedicated P-trap and stack connection.
Follow all local plumbing and electrical codes.
Leave the stud pocket open and do not install the finished wall until after the bath has been
installed. This installation is best done with access from the backside of the studs, particularly from
each side.
NOTICE: Follow all local plumbing and electrical codes.
If the installation site is in an area where frequent or prolonged power outages occur, Kohler Co.
recommends that a minimum 350 VA Uninteruptable Power Source (UPS) be installed as a backup
power source for the bath controller. This will ensure the door will open in the event of a power
outage. (A UPS is not required for the blower.)
Construct 2x4 or 2x6 stud
framing according to
the roughing-in information.
Position the rough plumbing.
Verify that the subfloor offers adequate support, and is flat and level.
Drain Access
Plumbing configuration
may vary.
To Accumulator
To Handshower
Hot
Cold
Floor Plan for Left-Hand Drain Model
16"
(406 mm)
10" (254 mm)
24-1/2"
(622 mm)
3-1/2"
(89 mm)
(LH) Drain
Cutout
7-3/4" (197 mm)
3-7/8"
(98 mm)
10" (254 mm)
10" (254 mm)
Drain Cutout
Three Drain Cutouts (required)
Drain
Cutout
1
2
3
5-1/2" (140 mm)
30" (762 mm)
33-1/4"
(845 mm)
Front Edge of
Receptor Tray
GFCI Protected Outlet
(Opposite Side of
Accumulator Supply)
1
(RH) Drain Cutout
9-3/4"
(248 mm)
3-7/8" (98 mm
Kohler Co. 7 1128535-2-F
- Installation Guide 1
- Important Information 2
- Factory-Assembled Features 3
- Table of Contents 4
- Tools and Materials 4
- Before You Begin 5
- Parts Identification 6
- 1. Construct the Framing 7
- 2. Confirm the Correct Cutout 9
- All Installations 10
- 5. Remove the Door 13
- 1128535-2-F 16 Kohler Co 16
- 7. Remove the Receptor Tray 17
- 8. Disconnect the Components 18
- Kohler Co. 19 1128535-2-F 19
- 9. Position the Bath 20
- 10. Level and Secure the Bath 22
- 12. Install the Receptor Tray 24
- 14. Install the Door 28
- 15. Attach the Counterweights 29
- 16. Connect the Components 31
- 17. Adjust the Bath Door 32
- GFCI-Protected Receptacle 36
- Power Supply 36
- Heating Surface 36
- 20. Confirm Airjet Operation 37
- Keypad Operation 38
- 22. Install the Finished Wall 41
- Troubleshooting 41
- Guide d’installation 54
- Notices du produit 55
- Pièces assemblées en usine 55
- Sommaire 56
- Outils et matériaux 56
- Avant de commencer 57
- Identification des pièces 58
- 1. Construire la charpente 59
- Toutes les installations 61
- 5. Retirer la porte 65
- 7. Retirer le bac collecteur 69
- 8. Déconnecter les composants 70
- 9. Positionner la baignoire 72
- 14. Installer la porte 80
- 15. Attacher les contrepoids 81
- 16. Connecter les composants 83
- Alimentation électrique 88
- Surface de chauffage 88
- Fonctionnement du clavier 89
- 22. Installer le mur fini 95
- Dépannage 95
- Guía de instalación 110
- Avisos sobre el producto 111
- Contenido 112
- Herramientas y materiales 112
- Antes de comenzar 113
- Identificación de las piezas 114
- Todas las instalaciones 115
- 5. Retire la puerta 121
- 8. Desconecte los componentes 126
- 9. Coloque la bañera 128
- 10. Nivele y fije la bañera 130
- 14. Instale la puerta 136
- 15. Fije los contrapesos 137
- 16. Conecte los componentes 139
- Tomacorriente protegido 144
- Superficie de calefacción 144
- Funcionamiento del teclado 145
- 22. Instale la pared acabada 151
- Guía para resolver problemas 151
- 1128535-2-F 166
Related products and manuals for Unknown Kohler K-1914-GRW-0
Unknown Kohler K7160AFCP User's Guide
(24 pages)
(24 pages)
Unknown Kohler K9000CP Specifications
(2 pages)
(2 pages)
Unknown Kohler K7160AFCP Specifications
(2 pages)
(2 pages)
Unknown Kohler K7160AFCP User's Guide
(1 pages)
(1 pages)
© 2020, manymanuals.com. All rights reserved. | 0.644 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals