Kohler K-1913-LW-47 Installation Guide Page 35
- Page / 156
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Confirm Heated Surface Operation (if equipped)
Keypad Operation
Power Icon - Turns the heater ON and OFF.
Heat/Temperature Indicator - The [Flame] icon illuminates yellow, orange, or red depending on the
heat level. Yellow indicates low heat, orange indicates medium heat, and red indicates high heat.
Up Arrow - Increases the temperature.
Down Arrow - Decreases the temperature.
NOTICE: The heater will remain on until it is manually turned OFF by pressing the [Power] icon.
NOTE: After 60 minutes of inactivity, the heater will automatically reset to low heat if the temperature
was set to medium or high.
NOTE: The heater will turn on at the last selected temperature setting.
Error Codes
Heat indicator blinking red - The heater is not functioning.
Heat indicator blinking yellow - The temperature sensor is not functioning or is loose.
Refer to the ″Troubleshooting″ section to troubleshoot any problems.
Confirm Heating System Operation
Press the [Power] icon on the user keypad.
Observe that the heat indicator turns yellow and the heater produces low heat.
Press the [Up] arrow. Verify that the heat indicator turns orange and the temperature increases.
Press the [Up] arrow a second time. Verify that the heat indicator turns red and the temperature
increases.
Press the [Down] arrow. Verify that the heat indicator turns orange and the temperature decreases.
Press the [Down] arrow a second time. Verify that the heat indicator turns yellow and the
temperature decreases.
Press the [Power] icon to turn the heater OFF.
Increase Temperature
Decrease TemperaturePower On/Off
Heat/Temperature Indicator
Kohler Co. 35 1128532-2-G
- Installation Guide 1
- Important Information 2
- Table of Contents 3
- Tools and Materials 3
- Before You Begin 4
- Parts Identification 5
- 1. Construct the Framing 6
- 2. Confirm the Correct Cutout 8
- All Installations 11
- 5. Remove the Door 12
- Kohler Co. 15 1128532-2-G 15
- 7. Remove the Receptor Tray 16
- 8. Disconnect the Components 17
- 9. Position the Bath 18
- 10. Level and Secure the Bath 20
- 14. Install the Door 26
- 15. Attach the Counterweights 27
- 16. Connect the Components 29
- 17. Adjust the Bath Door 30
- GFCI-Protected Receptacle 34
- Power Supply 34
- Heating Surface 34
- Keypad Operation 35
- 21. Install the Finished Wall 38
- Troubleshooting 38
- Guide d’installation 50
- Sommaire 51
- Outils et matériaux 51
- Avant de commencer 52
- Identification des pièces 53
- 1. Construire la charpente 54
- Toutes les installations 56
- 5. Retirer la porte 60
- 7. Retirer le bac collecteur 64
- 8. Déconnecter les composants 65
- 9. Positionner la baignoire 67
- 14. Installer la porte 75
- 15. Attacher les contrepoids 76
- 16. Connecter les composants 78
- Alimentation électrique 83
- Surface de chauffage 83
- Fonctionnement du clavier 84
- 21. Installer le mur fini 88
- Dépannage 88
- Guía de instalación 102
- Contenido 103
- Herramientas y materiales 103
- Antes de comenzar 104
- Identificación de las piezas 105
- Todas las instalaciones 106
- 5. Retire la puerta 112
- 8. Desconecte los componentes 117
- 9. Coloque la bañera 119
- 10. Nivele y fije la bañera 121
- 14. Instale la puerta 127
- 15. Fije los contrapesos 128
- 16. Conecte los componentes 130
- Tomacorriente protegido 135
- Superficie de calefacción 135
- Funcionamiento del teclado 136
- 21. Instale la pared acabada 140
- Guía para resolver problemas 140
- 1128532-2-G 154
Gai-tronics TDN9413A Stat-Alert Signaling Module Kit manuály
Uživatelské manuály a uživatelské příručky pro Komunikace Gai-tronics TDN9413A Stat-Alert Signaling Module Kit.
Poskytujeme 1 manuály pdf Gai-tronics TDN9413A Stat-Alert Signaling Module Kit ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comments to this Manuals