Kohler K-1914-GRW-0 Installation Guide Page 42
- Page / 168
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Troubleshooting (cont.)
It is normal to hear the compressor run for up to 90 seconds after the door is raised. The
compressor is located inside the door and is inflating the door seal.
If the door is fully raised for more than 20 minutes when there is no water in the bath,
the seals will automatically deflate.
It is normal to hear the solenoid valve, located inside the door, open and expel air when
the water level falls below the sensors. The valve is deflating the door seal.
Water coming from the bottom of the door and entering the receptor tray is normal when
it is caused by the bather moving about in the bath when it is completely full. Excessive
splashing will cause water to run over the top of the inflated seals into the receptor tray.
Water dripping into the receptor tray as the seals deflate is normal. Water collects on the
seal during use and falls into the receptor tray when the seals deflate.
Troubleshooting the Airjet System
Symptoms Probable Causes Recommended Action
1. Bath with airjets does not
start.
A. No power to blower motor. A. Set/reset GFCI or RCD breaker;
check wiring.
B. User keypad cable loose or
damaged.
B. Check wire connections. If
necessary, replace user keypad
cable.
C. User keypad does not work. C. Check wire connections. Replace
user keypad.
D. Blower motor does not work. D. Replace blower motor.
2. Blower motor starts, but
there are few or no
bubbles.
A. Blower motor is disconnected. A. Connect blower motor to air
harness.
B. Blower motor air flow is
restricted.
B. Clean the area around the blower
motor. Ensure adequate
ventilation.
3. Bath stops automatically
before 18 minutes.
A. GFCI or RCD trips. A. Identify source of fault and
correct.
B. Motor overheated and protection
device activated.
B. Check for blockage at motor
vents. Remove blockage and
allow motor to cool.
4. Bath does not stop
automatically after 22
minutes.
A. Blower motor does not work. A. Replace blower motor.
5. Blower motor does not
stop when power button
on user keypad is
pressed.
A. User keypad cable loose or
damaged.
A. Check wire connections. If
necessary, replace user keypad
cable.
B. User keypad does not work. B. Replace user keypad.
6. Blower motor operates
but variable speed feature
does not work.
A. User keypad cable loose or
damaged.
A. Check wire connections. If
necessary, replace user keypad
cable.
B. User keypad does not work. B. Replace user keypad.
C. Blower motor does not work. C. Replace blower motor.
7. Automatic purge cycle
does not occur.
A. Blower motor does not work. A. Replace blower motor.
1128535-2-F 42 Kohler Co.
- Installation Guide 1
- Important Information 2
- Factory-Assembled Features 3
- Table of Contents 4
- Tools and Materials 4
- Before You Begin 5
- Parts Identification 6
- 1. Construct the Framing 7
- 2. Confirm the Correct Cutout 9
- All Installations 10
- 5. Remove the Door 13
- 1128535-2-F 16 Kohler Co 16
- 7. Remove the Receptor Tray 17
- 8. Disconnect the Components 18
- Kohler Co. 19 1128535-2-F 19
- 9. Position the Bath 20
- 10. Level and Secure the Bath 22
- 12. Install the Receptor Tray 24
- 14. Install the Door 28
- 15. Attach the Counterweights 29
- 16. Connect the Components 31
- 17. Adjust the Bath Door 32
- GFCI-Protected Receptacle 36
- Power Supply 36
- Heating Surface 36
- 20. Confirm Airjet Operation 37
- Keypad Operation 38
- 22. Install the Finished Wall 41
- Troubleshooting 41
- Guide d’installation 54
- Notices du produit 55
- Pièces assemblées en usine 55
- Sommaire 56
- Outils et matériaux 56
- Avant de commencer 57
- Identification des pièces 58
- 1. Construire la charpente 59
- Toutes les installations 61
- 5. Retirer la porte 65
- 7. Retirer le bac collecteur 69
- 8. Déconnecter les composants 70
- 9. Positionner la baignoire 72
- 14. Installer la porte 80
- 15. Attacher les contrepoids 81
- 16. Connecter les composants 83
- Alimentation électrique 88
- Surface de chauffage 88
- Fonctionnement du clavier 89
- 22. Installer le mur fini 95
- Dépannage 95
- Guía de instalación 110
- Avisos sobre el producto 111
- Contenido 112
- Herramientas y materiales 112
- Antes de comenzar 113
- Identificación de las piezas 114
- Todas las instalaciones 115
- 5. Retire la puerta 121
- 8. Desconecte los componentes 126
- 9. Coloque la bañera 128
- 10. Nivele y fije la bañera 130
- 14. Instale la puerta 136
- 15. Fije los contrapesos 137
- 16. Conecte los componentes 139
- Tomacorriente protegido 144
- Superficie de calefacción 144
- Funcionamiento del teclado 145
- 22. Instale la pared acabada 151
- Guía para resolver problemas 151
- 1128535-2-F 166
Related products and manuals for Unknown Kohler K-1914-GRW-0
Unknown Kohler K7160AFCP User's Guide
(24 pages)
(24 pages)
Unknown Kohler K9000CP Specifications
(2 pages)
(2 pages)
Unknown Kohler K7160AFCP Specifications
(2 pages)
(2 pages)
Unknown Kohler K7160AFCP User's Guide
(1 pages)
(1 pages)
© 2020, manymanuals.com. All rights reserved. | 1.362 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals